Happy-Trails Pannier Mount Kit Point1

Already have panniers? Here is the puck kit for mounting them on your new SU rack.
$38.00
SKU
HTPMKXXX.1

Our mount kits make it a cinch to take your panniers on and off your Happy Trails Point1 design SU rack. Note that your SU rack is a Point1 design if it has a pressed insert for the upper mounts.

The kit contains 2 pucks for each pannier (total of 4). The pucks are permanently attached with hex head bolts to the bottom of the panniers, and hold the shear weight of the pannier. The upper two mounts on each pannier are secured via a plastic knob (3/8" bolt) turned into a threaded insert on the SU rack. Large washers on the inside of the pannier spread the load.

MK750.1 mounts cases to Happy-Trail Point1 SU racks with 3/4" (.750" or 19.05 mm) tubing.

MK625.1 mounts cases to Happy-Trail Point1 SU racks built with 5/8" (.625" or 15.875 mm) tubing (5/8" tubing applies only to BMW Oilheads: R11xxGS; R1200GS)


Note: Our puck system now employs hex head bolts instead of allen head's because customers reported issues with the head being stripped.

All Happy Trails products are crafted in Boise, Idaho

INSTALL INSTRUCTIONS MK625.1
        INSTALL INSTRUCTIONS MK750.1

Write Your Own Review
You're reviewing:Happy-Trails Pannier Mount Kit Point1

Product Faqs

Ask a Question




Ask a Question


Sort by   
  • I have a 2008 Buell U'ysses with tne oem Hepco & Becker rack. Will this mounting kit will fit the racks?
    Question by: Yamil Ruiz on 2018-01-13 21:00:00

    Yowill need THIS KIT check your tube size it should be 5/8" so you use the 625 kit.  Add the SWM kit in the drop down to make the mounting easier.

    Answer by: Tim on 2018-01-13 16:00:00
  • I need to get some replacement knob nuts, can you tell me what size these are? Thanks.
    Question by: Derek on 2017-10-23 15:45:00

    They are 8mm by 1.25 pitch.

    Answer by: Tim on 2017-10-23 11:45:00
  • I have a bike with a KLRE 2011 SU Rack with Long Slots (part number HTP4-8-1.1) that has some pucks missing. Is this the correct mounting kit to replace the missing parts?
    Question by: Ben C on 2017-06-21 04:38:00

    Choose the 3/4 or 750 option HTPMK750.1 is the part number.

    Answer by: Tim on 2017-06-21 00:38:00
  • I have Givi side racks for mounting Monokey Luggage . The rack tubing diameter is 5/8 in . but it has 4 rubber bumper pads around the rack that add about 1/8 in thickness . If I choose to install aluminum panniers, which set do you advise ? the MK625 or MK 750? What is the difference between the two ?
    Question by: Nevri Cebaf on 2016-09-21 02:53:00

    You would the 625 kit. The 625 kit is 5/8" (.625"). I wouls suggest you remove the rubber bumpers.

    Answer by: Tim on 2016-09-20 22:53:00
  • I have the KTM_Powerpart pannier rack (tubular frame all around). 2016 KTM 690 Enduro R. Is there a way to fit these brackets to my Pelican Air 1555 Case to the rack?I noticed that the bracket was designed for a square frame. Do you have any other options or recommendations on how to make them work?
    Question by: Abner on 2016-07-30 21:25:00

    You will need to determine the OD of your tube; it could be .625", .710' or .750".

    One you have done that the Universal Mount Kit is what you would need. I would also suggest including the SWM option. Read these instructions to give you  better idea on how to use the mount kit.

    The kit works on round or square tubing.

    Answer by: Tim on 2016-07-30 17:25:00